Melting point of cis norbornene 5 6 endo dicarboxylic anhydride VideoDiels-Alder Lab
Melting point of cis norbornene 5 6 endo dicarboxylic anhydride - seemsOC TYI'l. Definitions for these qualifiers are provided below. This flag is usually used for a tentatively identified compound, where the identification is based on a mass spectral library search. NJ The analysis indicates the present of an analyte for which there is presumptive evidence to make a tentative identification and the associated numerical value represents its approximate concentration. The lower of the two results is reported. R Indicates the data are unusable. melting point of cis norbornene 5 6 endo dicarboxylic anhydride
For use only as setting agent for protein. Phenothiazine For use only as antioxidant in dry rosin size. Phosphoric acid esters and polyesters and their sodium salts of triethanolamine formed by the reaction of triethanolamine with polyphosphoric acid to produce a mixture of esters having an average nitrogen content of 1.
Poly[acrylamide-acrylic acid- N- dimethyl-aminomethyl acryl- amide], produced by reacting 2.
Polyacrolein 1 part -sodium bisulfite 0. Poly[acrylamide-acrylic acid- N melging dimethylaminomethyl acrylamide] C. Registry No. Polyamide-epichlorohydrin water-soluble thermosetting resins [CAS Reg. As a retention aid employed prior to the sheet-forming operation in the manufacture of paper and paperboard and limited to use at a level not to exceed 0. The finished paper or paperboard will be used in contact with food only of the types identified in paragraph c of this section, table 1, under types I and IV-B and under conditions of use described in paragraph idcarboxylic of this section, table 2, conditions of use F and G. Polyamide-epichlorohydrin water-soluble thermosetting resin CAS Reg.
Polyamide-epichlorohydrin water-soluble thermosetting resins prepared by reacting adipic acid, isophthalic acid, itaconic acid or dimethyl glutarate with diethylenetriamine to form a basic polyamide and further reacting the polyamide with one of the following: For use only in the manufacture of paper and paperboard under conditions such that the resins do not exceed here. Epichlorohydrin and sodium hydrosulfite mixture.
Polyamidoamine-ethyleneimine-epichlorohydrin resin prepared by reacting hexanedioic acid, N - 2-aminoethyl -1,2-ethanediamine, chloromethyl oxirane, ethyleneimine aziridineand polyethylene glycol, partly neutralized with sulfuric acid CAS Reg. Polyamidol-epichlorohydrin modified resin produced by reacting glutaric acid dimethyl ester with diethylene-triamine to produce a basic polyamide which is modified by http://rectoria.unal.edu.co/uploads/tx_felogin/why-do-cosmetic-for-our-business-which/foreclosure-in-psychology.php with formaldehyde and further reacted with epicholorohydrin to form a water soluble cationic resin having a nitrogen content of Polyamine-epichlorohydrin resin produced by the reaction dicabroxylic N,N- dimethyl-1,3-propanediamine with epichlorohydrin and further reacted with sulfuric acid, Chemical Abstracts Service Registry Number , such that the finished resin has a maximum nitrogen content of The finished resin has a nitrogen content of 5.
Polyamine-epichlorohydrin water soluble thermosetting resin prepared by reacting hexamethylenediamine with 1,2-dichloroethane to form a prepolymer and further reacting this prepolymer with epichlorohydrin.
This resin is then reacted with nitrilotris methylene-phosphonic acidpentasodium salt, such that the finished resin has a nitrogen content of 5. Polyamine resin produced by the reaction of 1,2-dichloroethane with bis hexamethylene triamine and higher homologues oof that the finished resin has homosexualitt nitrogen content of Polyaminoamide-epichlorohydrin modified resin produced by reacting adipic acid with diethylenetriamine to produce a polyamide which is modified by reaction with diethylaminopropylamine and further reacted with dichloroethyl ether to form a polyamide intermediate.
This polyamide intermediate is then reacted with dicxrboxylic such that the finished resins have a nitrogen content of Poly diallyldimethylammonium chloride CAS Reg. The level of residual monomer is not to exceed 1 percent by weight of the polymer dry basis For use only: 1.
As a pigment dispersant in coatings at a level not to exceed 3.
Poly 1,2-dimethylvinylpyridinium methyl sulfate having a nitrogen content of 5. Polyethyleneamine mixture produced when 1 mole of ethylene dichloride, 1. Polyethylene glycol dilaurate For use only as an adjuvant employed in the manufacture of paper and paperboard prior to the sheet-forming operation. Polyethylene glycol dioleate Polyethylene glycol esters of coconut oil fatty acids Polyethylene glycol esters of tall oil fatty acids Polyethylene glycol monolaurate.]